Heater failed in the attic?
Shut the cold-water valve and cut the gas or power, then check the ceiling below for water. For a gas smell, get out first and dial 911, then your gas utility: CoServ Gas at 844-330-0763 or Atmos Energy at 866-322-8667. Call us at (682) 284-0966 to schedule the replacement.
Many Frisco homes went up during the 2000s and 2010s growth years, and many original water heaters are now due for replacement. Frisco’s installation rules mean a straight swap isn’t always a straight swap. An attic heater has to come out through an opening big enough to remove it, the relief line can’t end on a patio, and a closed system needs expansion control. We check all of that before quoting.
Heater still repairable? See water heater repair in Frisco. Considering tankless? See tankless water heaters in Frisco.
Frisco’s original heaters are coming due
The Census (ACS 2020–2024) counts about 80,400 homes in Frisco. About 35% were built in the 2000s and about 40% in the 2010s. Heaters installed in the 2000s are now 15 to 25 years old, and the first 2010s heaters are past 10. That’s a large share of the city replacing heaters within a few years of each other.
Frisco replacements by home age
Older Frisco
About 18% of homes. These are often on a second or third heater, so we check what earlier installers left behind.
Original heaters aging out
About 35% of homes. This is the biggest replacement group in Frisco right now.
Next in line
About 40% of homes. Attic and garage heaters from early in the decade are reaching replacement age.
Built since 2020
About 7% of homes. Replacement is rare unless a heater was damaged.
Frisco’s installation requirements, applied to a replacement
City of Frisco Water Heater Installation Requirements
- Attic heaters: a passageway at least 30 inches high with continuous solid flooring at least 24 inches wide, a 30-by-30-inch level service space in front, and an opening large enough to remove the heater.
- Electric heaters: a means of disconnect or a permanent lockout at the heater’s breaker in the panel.
- Gas venting: at least 5 feet of vertical rise, a properly installed cap, collar and flashing, secured vents, and 1 inch of clearance for double-wall vent (6 inches for single-wall).
- Connections: dielectric unions or brass fittings where dissimilar metals meet, and gas flex replaced as the manufacturer instructs.
- Gas shutoff and sediment trap: an approved shutoff in the same room within 6 feet, and sediment traps as required by the IRC and IFGC.
- Relief line: runs outside, ends at least 6 inches above grade, has a union, and isn’t trapped or ended on a sidewalk or patio.
Frisco requires a permit for water heater replacement, and a carbon monoxide alarm in an existing home when permitted work is done. Staggs Plumbing is registered with the City of Frisco and pulls the permit itself.
Choosing the replacement
| Choice | Consider it when | Frisco detail |
|---|---|---|
| Same tank, same place | It worked well and fits the space | Bring the pan, relief line and venting up to the requirements |
| Move it out of the attic | You want easier access and less leak risk | New vent, gas and drains at the new location |
| Larger tank | You run out of hot water | Check the gas supply and attic opening size |
| Tankless | You want endless hot water | Gas sizing, new vent and condensate per Frisco’s tankless facts |
Pressure, expansion and Frisco water
Frisco’s water report notes that pressure at your home may be controlled by a pressure-reducing valve on your service line. That makes a closed system, and Frisco’s requirements call for thermal expansion control. The water comes from NTMWD’s Wylie plant at 96 to 200 ppm total hardness, so a new tank should be flushed periodically.
How a Frisco replacement goes
Inspect
We check the old heater, its location, access, venting, drains and gas or electrical.
Quote
You get a written flat-rate price for each option, including the permit and code items.
Replace
We remove the old heater, install the new one to Frisco’s requirements, and test it.
Close out
The city inspects the work. We make sure a CO alarm is in place if one is needed.
Replacing a heater in Frisco? Start here.
Helpful to have:
- The heater’s location: attic, garage or closet.
- The data plate with size, fuel and age.
- Your gas utility: CoServ Gas or Atmos.
- Whether you have CO alarms in the house.
- Call (682) 284-0966 and we’ll price each option in writing.
Frisco neighborhoods we serve
We replace water heaters in Frisco’s 75033, 75034, 75035 and 75036 ZIP codes, in both Collin and Denton counties.
Our Plano headquarters is just south of Frisco.
Frisco water heater replacement FAQ
Is a permit required to replace a water heater in Frisco?
Yes. Frisco’s code amendments say water heater replacement isn’t exempt from permits and inspections.
Is a carbon monoxide alarm part of the job?
Frisco requires a CO alarm in an existing home when permitted work is done, and a water heater replacement is permitted work.
Can a bigger heater go in my attic?
Only if it fits Frisco’s attic rules, including an opening large enough to remove the heater and a 30-by-30-inch service space. We check before quoting.
Do electric heaters have special rules?
Yes. Frisco requires a means of disconnect or a permanent lockout at the heater’s breaker.
Which gas utility serves my Frisco home?
Most Frisco homes with gas are on CoServ Gas; the rest are on Atmos Energy. Your bill shows which one serves you.
Should I replace with tankless?
It depends on your gas supply, vent route and budget. We’ll price both so you can compare.