Skip to main content
Water Heater Repair · Frisco, TX

Water Heater Repair in Frisco, TX

Most Frisco homes were built after 2000, and many still have the water heater the builder put in. Add NTMWD water, which the city’s own report calls moderately hard, and many of those heaters are starting to fail. We find the problem, give you a written flat-rate price, and if the heater needs replacing, take care of the Frisco permit and inspection.

Texas Master Plumber #M-17697 · Family-owned since 1990 · Open 24/7

Quick Answer

Frisco buys its treated water from the North Texas Municipal Water District’s Wylie plant, and the city’s 2025 report puts total hardness between 96 and 200 ppm. Most Frisco repairs involve sediment, a failed element or thermostat, a gas control or igniter, or relief valve drips caused by thermal expansion. Frisco doesn’t require a permit for minor repairs like a heating element replacement, but replacing the water heater itself requires a permit and city inspection.

Texas Master Plumber #M-17697 · 24/7 emergency service · Flat-rate written estimates
License M-17697 Family-owned since 1990 Gas and electric heaters 24/7 emergency service Flat-rate written estimates

Water heater leaking in Frisco?

Close the cold-water valve on the line feeding the heater. Turn a gas unit’s control to OFF or switch off an electric unit’s breaker. If you smell gas, get out first. Frisco is split between two gas utilities, so call 911 and then CoServ Gas (844-330-0763) or Atmos Energy (866-322-8667), whichever is on your bill. Our Frisco gas leak page explains which areas each serves. Then call us at (682) 284-0966.

Frisco’s water comes from NTMWD’s Wylie Water Treatment Plant, which draws on Lavon Lake, Bois d’Arc Lake, Lake Texoma, Jim Chapman Lake, Lake Tawakoni and the East Fork Water Reuse Project. The city’s 2025 report (published July 2026) explains that the water is “moderately hard” because of minerals in North Texas lakes, and that those minerals leave lime scale on plumbing fixtures. A water heater sees that scale first.

Ready to replace? See our Frisco water heater replacement page or tankless water heaters in Frisco. Water spreading fast? See emergency plumbing in Frisco.

Frisco: newer homes, aging first heaters

The Census (ACS 2020–2024) counts about 80,400 homes in Frisco, with a median build year of 2009. About 95% were built in 1990 or later, and about 41% from 1990 through 2009. Frisco’s population went from 33,714 in 2000 to 200,509 in 2020. A house built in the 2000s that still has its original water heater has a tank that’s 15 years old or more.

2009
median year a Frisco home was built
~35%
of homes built in the 2000s
96–200
ppm total hardness, 2025 report

Frisco heaters by era

Before 2000

Downtown and early subdivisions

About 18% of homes, near the Rail District and the first neighborhoods off Preston Road. Many of these heaters have already been replaced; we check that the relief line and pan drain meet current rules.

2000s

The first boom

About 35% of homes. Many builder-installed tanks from this decade are now 15 to 25 years old, and sediment builds up over that time.

2010s

The biggest decade

About 40% of homes. These heaters are newer. If the home has a pressure-reducing valve on its service line, thermal expansion control matters.

2020–today

Newest homes

About 7% of homes. With heaters this new, we look first at parts, settings and pressure, not the tank.

Frisco water and what it does inside a heater

From Frisco’s 2025 water quality report

  • Supplier: the City of Frisco (system TX0430005) buys treated water from NTMWD’s Wylie Water Treatment Plant.
  • Hardness: 96 to 200 ppm total hardness as calcium carbonate, about 5.6 to 11.7 grains per gallon. The city calls NTMWD’s water “moderately hard”; the top of the range is very hard on the USGS scale.
  • The city’s explanation: minerals such as calcium bicarbonate and magnesium carbonate come from North Texas lakes. They aren’t a health risk, but they leave spots and lime scale.
  • Water pressure: the city notes that pressure at your home may be controlled by an individual pressure-reducing valve on your service line. For pressure questions, call Public Works at 972-292-5800.

That pressure-reducing valve matters for your water heater. When it closes off the system, heated water has nowhere to expand, and Frisco’s installation rules require a means of thermal expansion control on a closed system.

What we repair on Frisco water heaters

Symptom Likely cause Repair
Relief valve drips after showers Thermal expansion on a closed system; expansion tank missing or waterlogged Check pressure, then recharge or replace the expansion tank
Not enough hot water (electric) Burned-out or scaled heating element, or a failed thermostat Replace the element or thermostat
Gas heater won’t light Igniter, flame sensor, thermocouple or gas control Find the failed part and replace it
Rumbling, slow recovery Sediment on the tank bottom Flush the tank; replace it if the bottom is damaged
Tankless shows an error code Scale in the heat exchanger or a clogged inlet filter Descale and clean per the manufacturer
Water in the pan Leaking fitting, drain valve or tank Repair the fitting or valve; replace a leaking tank

Frisco permits: repair vs. replacement

How the City of Frisco draws the line

  • Minor repairs, no permit: the city’s “Simple Facts About Appliance Repair and Replacement” names a heating element replacement on a water heater as a minor repair that doesn’t need a permit or inspection. The licensed contractor is still responsible for meeting code.
  • Replacement, permit required: water heater replacement requires a permit, and Frisco’s code amendments state that it’s not exempt from permits and inspections.
  • Who can pull it: the person doing the work, as a registered licensed contractor, or a homeowner working on their own primary residence.
  • Carbon monoxide alarm: when permitted work is done, Frisco requires a carbon monoxide alarm in an existing home.
  • Installation rules: pans under every heater with a drain to the outside 6 to 24 inches above grade; a relief line with a union, not trapped and not ending on a sidewalk or patio; thermal expansion control on closed systems; an 18-inch ignition-source height in garages; and a gas shutoff in the same room, within 6 feet.

Staggs Plumbing is registered with the City of Frisco and pulls the permit itself. On a repair call, if your heater is close to replacement, we’ll also tell you what Frisco’s rules will require, like a CO alarm or an expansion tank, so it’s in the price from the start.

How a Frisco repair call works

1

Diagnose

We check the heater, relief valve, pan and drain, house water pressure and expansion tank, and the gas or electric supply.

2

Written price

A flat-rate price before any work. If replacement makes more sense, you’ll see that price too.

3

Repair

Elements, thermostats, gas parts, expansion tanks and flushes are usually done in one visit.

4

Permit if replaced

A replacement is permitted with the City of Frisco and inspected.

Repair it or replace it?

  • Repair when a part has failed and the tank is sound. In Frisco, many of these repairs don’t need a permit.
  • Replace once the tank itself leaks or the hot water runs rusty. A builder heater from the 2000s is a common candidate.
  • Go tankless if you want the space back or endless hot water. Plan on periodic descaling with Frisco’s water.

Water heater problem in Frisco? Start here.

Take these steps:

  1. Close the cold-water valve to the heater if it’s leaking.
  2. Shut off the heat source: gas control to OFF, or the breaker off.
  3. Gas smell? Leave first, then call 911 and CoServ (844-330-0763) or Atmos (866-322-8667).
  4. Relief valve dripping but no leak? Note when it happens; it often points to thermal expansion.
  5. Call (682) 284-0966 for a diagnosis and written price.
Relief valve blowing hot water or steam? Turn off the gas or power and call immediately. Don’t plug or cap the valve or its line.

Frisco neighborhoods we serve

We serve Frisco ZIP codes 75033, 75034, 75035 and 75036, on both the Collin and Denton county sides: downtown and the Rail District, Stonebriar and the SH 121 corridor, the Preston Road neighborhoods, and the newer communities north of Eldorado Parkway and west of FM 423.

From our Plano headquarters, Frisco is a short drive up the Dallas North Tollway.

Frisco water heater FAQ

Who supplies Frisco’s water?

The City of Frisco buys treated water from the North Texas Municipal Water District’s Wylie Water Treatment Plant. Its sources include Lavon Lake, Bois d’Arc Lake, Lake Texoma, Jim Chapman Lake, Lake Tawakoni and the East Fork Water Reuse Project.

Is Frisco’s water hard?

The city calls it moderately hard. The 2025 report lists 96 to 200 ppm total hardness, about 5.6 to 11.7 grains per gallon, which is enough to scale water heaters and tankless units.

Does a water heater repair need a permit in Frisco?

Not for minor repairs. Frisco names a heating element replacement as a minor repair that doesn’t need a permit. Replacing the whole water heater does need a permit and inspection.

Why does my relief valve drip?

If your Frisco home has a pressure-reducing valve on its service line, the plumbing is a closed system. Without working thermal expansion control, pressure builds as water heats and the relief valve lets some out. A worn relief valve can also drip.

Will I need a carbon monoxide alarm?

If the work requires a permit, such as a water heater replacement, Frisco requires a carbon monoxide alarm in an existing home. Many homes already have one.

Who do I call about a gas smell in Frisco?

Leave first and call 911. Then call your gas utility: CoServ Gas at 844-330-0763 or Atmos Energy at 866-322-8667. Your gas bill shows which one serves you.

Newer homes. Aging heaters.

Water heater repair in Frisco, TX

Staggs Plumbing is a family-owned, licensed Texas master plumber (License #M-17697) serving North Texas since 1990, with headquarters just south in Plano. You get a written flat-rate price before any work, and we pull the Frisco permit if the heater needs replacing.

Call (682) 284-0966

What Our
Customers Say

"Great price! Staggs Plumbing was incredible - they replaced our entire system from cast iron to PVC in less than 3 days, with no cut corners and incredible attention to detail. Their prices were fair, communication was incredible, and they even took care of some dry wall replacement at no cost to us after the job was done.. we are so pleased and will for sure call Staggs anytime in the future!"
"A little miscommunication up front regarding messages left over the past weekend but the Plumbers showed up as scheduled. They did a great job and were very professional as always. Pleased with their repairs and a fair price."

Real results from every plumbing project.

24/7 Emergency Service

We're available day and night to handle urgent plumbing issues.

Flexible Scheduling

Choose a time that fits your schedule — we work around your convenience.

Get In Touch

"*" indicates required fields

Date (optional)